Cement-based plaster           ARTRA - Plas

 

Description

Cement-based, one component, a chemical added, machine

or ready-to-apply thin plaster.

 

Usage areas:

• indoors and outdoors,

• Wall and ceiling,

• On surfaces such as rough plaster, concrete and gross concrete

paint and decorative coatings prior to a flat

used to obtain surface.

 

Advantages:

• Provides a smooth surface.

• Saves time and labor.

• It provides high adherence and stability, does not sag.

• Easy and fast application of both machine and hand

provides.

• More than outdoor conditions than black plaster

It is resistant.

 

Surface Preparation:

• Application surface is cured and robust

should be careful.

• Application surface is powder, oil, tar, tar, paint, silicone,

adhesion such as curing agent, detergent and mold oils

preventive substances.

• Repair for the repair of cracks and holes on the surface

Mortars should be used.

• The concrete surfaces should be primed with Plaster Primer before gross concrete applications.

• The application surface should be moistened.

 

Preparation of Mortar:

• 25 kg ARTRA  Plas, Fine Plaster approx. 5 - 6 liters of clean water

preferably with a low-speed mixer.

mix and use in such a way that no lumps remain.

• The mixture in the container should be consumed within 2-3 hours.

 

Application Information:

• Material spraying machine or trowel

should be applied and spread over the entire surface of equal thickness.

• The surface should be smoothed with a gauge after the application.

• The application of fine plaster should not exceed 25 mm.

• The plaster starts to harden before the time is missed

it should be smoothed with a trowel.

• Combination of different materials such as concrete, brick

and cracking of window, door corners

plaster mesh should be used.

• Air temperature after the application is completed

if it is high, it is moistened until it gets the plaster setting.

• Weather conditions and application thickness for paint

Depending on the need to wait at least 7 days.

 

Consumption:

1.4 - 1.7 kg / m2

 (For 1 mm thickness)

Attention:

• At temperatures below + 5 ° C and above + 35 ° C

Avoid application.

• Lime, cement, sand, and plaster into the material

Do not add foreign substances such as.

• Pay attention to the amount of water added to the mortar.

Do not add more water than necessary.

• Risk of freezing within 24 hours or

without application in direct sun and wind avoid

 

Packing:

In 40 kg kraft paper bags

 

Shelf life:

In humid environments and unopened packaging

It can be stored on pallet for 10 months with 10 layers stacking.

 

Health and Safety:

As with all chemical products

during the storage of food products, skin, eyes and mouth

contact. During application, work and

protective clothing, protective clothing

gloves, goggles and mask should be used. By accident

If swallowed, seek medical advice. In contact with skin

Wash with plenty of water. Out of reach of children

should be stored in places.

 

Technical specifications

Appearance: Gray fine powder

Powder Density: ~ 1,40 kg / lt

Water Mixing Ratio: 8.8 - 10.4 It water / 40 kg powder

Application Temperature: + 5 ° C to + 35 ° C

Compressive Strength: CS IV; ≥ 6 N / mm2 (EN 1015-11)

Bond Strength: ≥ 1 N / mm2 (EN 1015-12)

Capillary Water Absorption: W1; C ≤ 0.40 kg / m2 (EN 1015-18)

Water Steam ›Permeability Coefficient (µ): ≤ 25 (EN 1015-19)

Application Thickness: 5 - 25 mm

Start-up Time: 24 hours